Запасные части к компрессорам Sabroe SAB128

Pos.	Designation	No	Part no.
	Complete compressor for male drive		4161-074
	Complete compressor for female drive		4161-073
	Compressor housing
10	Rotor housing	1	3011-021
	Bearing cover at suction end
20	Bearing cover	1	3013-143
21	O-ring dia 304.39 x 3.53	1	1331-112
22	Cylindrical pin dia 12 x 40	2	1445-084
23	Socket cap screw M12 x 35	16	1413-387
24	Threaded plug with collar 1/2"	1	1343-027
25	Gasket dia 27/21 x 1,5	1	2356-133
	Bearing cover at discharge end
40	Cover	1	3013-052
43	Cylinder screw M10 x 35	6	1413-373
44	Adjusting screw	2	2111-122
45	Locking screw M6x 10	4	1413-231
	Capacity regulating cylinder
50	Cylinder	1	3043-010
51	O-ring dia 82.14x3.53	1	1331-077
52	Cylinder screw M10 x 35	3	1413-373
	Cover for capacity regulating cylinder
60	Cover	1	3013-193
61	O-ring dia 88.49 x 3.53	1	1331-079
62	Cylinder screw M8 x 25	4	1413-357
	Housing for capacity indicator
70	Housing	1	3045-002
71	Cylinder screw M6 x 30	4	1413-343
72	Cover for capacity indicator	1	3045-003
73	Cylinder screw M6 x 50	4	1413-347
74	O-ring dia 98.02 x 3.53	1	1331-081
75.1	Glass for indicator	1	3045-006
	Shaft seal cover
80	Shaft seat cover	1	3013-051
81	O-ring dia 85.32 x 3.53	1	1331-078
82	Cylinder screw M10 x 35	4	1413-373
83	Driving pin dia 4 x 8	1	1446-011
86	Hose connection 1/4"	1	1343-025
87	Plastic hose 3/16"	1	1241-190
88	Plug 1/4"	1	1345-025
89	Gasket dia. 19/14 x 1.5	1	2356-124
	Cap cover
90	Cap cover	1	3013-050
91	O-ring dia 85.32 x 3.53	1	1331-078
92	Cylinder screw M10 x 35	4	1413-373
	Cover for slide stop
100	Cover	1	3013-057
101	O-ring dia 66.27 x 3.53	1	1331-072
102	Cylinder screw M10 x 35	3	1413-373
103	Retainer for spindle bearings	1	3044-013
104	Cylinder screw M6 x 20	4	1413-341
105	Locking plate	1	2114-043
	Rotors and suction end bearings
110	Set of rotors for SAB 128H, female drive	1(F)	3024-018
110	Set of rotors for SAB 128 H, male drive	1(M)	3024-109
111	Roller bearing	2	1513-016
112	Retainer pin for male rotor	1	3021-012
113	Oil splash ring	1	1437-217
114	Thrust washer	2	3021-035
115	Cylinder screw M12 x 35	2	1413-387
118	Driving pin dia 4 x 8	1	1446-019
119	Retainer pin for female rotor	1	3021-017
120	Balance piston, suction end	1	3025-007
	Discharge end bearings, female rotor
130	Balance piston dia. 64	1	3025-016
131	Radial roller bearing dia. 40/90 x 33	1	1513-016
132	Four point bearing dia. 40/90 x 23	1	1513-027
133	Set of shims dia- 70/90 for adjusting the	1	2124-080
	clearance between the rotor and outlet port
	comprising: 1 off thickness 0.49mm
	1 - 0.52mm
	1 - 0.55 mm
	1 - 0.58 mm
	1 - 0.61 mm
	1 - 0.64mm
	1 - 0.67mm
	Discharge end bearings, male rotor
135	Balance piston dia 64	1	3025-016
136	Radial roller bearing dia 45/100 x 36	1	1513-012
137	Four point bearing dia 45/100 x 25	1	1513-028
138	Set of shims dia 80/100 for adjusting the	1	2124-081
	clearance between the rotor and outlet port
	comprising: 1off thickness 0.49mm
	1 - 0.52mm
	1 - 0.55 mm
	1 - 0.58 mm
	1 - 0.61 mm
	1 - 0.64mm
	1 - 0.67mm
	Discharge ports
140	Discharge port for male rotor	1	3031-037
141	Discharge port for female rotor	1	3031-038
142	Socket cap screw M8 x 120	6	1413-314
143	Sealing ring dia 13/8	6	3049-006
144	Set screw M 10x20	2	1413-252
145	Set screw M1 Ox 10	2	1413-253
146	Blank off screw	2	1343-027
147	Locking screw M 10 x 10	2	1413-253
148	Adjusting screw M10 x 20	2	1413-032
149	Gasket	2	1331-427
	Parts for adjusting rotors
151	Thrust cover for male rotor	1	3013-053
152	O-ring dia 91.67 x 3.53	1	1331-080
153	Thrust cover for female rotor	1	3013-054
154	O-ring dia 82.14 x 3.53	1	1331-077
	Shaft seal
160	Shaft seal type 680.	1	1332-161
	Suction filter
170	Suction filter	1	3042-081
171	Set screw M6 x 10	3	1413-231
	Adjusting system for V_i-slide
180	Spindle	1	3044-012
182	Spacer ring	1	3044-014
183	Sealing ring dia 28/22	1	1331-503
184	O-ring dia 44.04 x 3.53	1	1331-065
186	Spindle bearing	2	1512-015
	Slide stop
190	Slide stop (included in pos. 192)
	Man. Vi-slide
191	Spring	1	1523-014
192	Slide control (including slide stop, pos. 190)	1	3044-071
193	Socket cap screw M10 x 25	1	1413-371
	Capacity regulating slide
200	Slide	1	3043-175
201	Inner piston part	1	3043-075
202	Outer piston part	1	3043-076
203	O-ring dia 53.57 x 3.53	1	1331-068
204	Sealing ring dia 90/80	1	1332-118
205	Cylindrical pin dia 6 x 12 (incl. in pos no 207)	(1)	1445-075
206	Cylinder screw M6 x 25	4	1413-342
207	Piston rod	1	3043-112
208	Tape bearing	2	2132-105
209	O-ring dia 9,12 x 3,53	1	1331-215
	Spindle for capacity indication
210.1	Spindle	1	3045-057
216	Magnetic coupling	1	3045-061
217	O-ring dia. 44,12 x 2,62 (incl. in pos. 216)	(1)	1331-146
218	Hexagon head screw M4 x 16 (incl. in pos. 216)	(1)	1413-320
219	Hexagon head screw M4 x 20 (incl. in pos. 216)	(2)	1413-322
	Capacity indication
221	Indicator dial	1	3045-001
223	Cylinder screw M4 x 10	1	1413-319
224	Supporting ring	1	2356-155
226	Locking washer DC 15/8,4	1	1437-054
227	Locking washer DC 8/4.3	1	1437-060
	Suction gas inlet
252	O-ring dia 190.09 x 3.53	1	1331-105
253	Inlet flange	1	3013-130
254	Cylinder screw M16 x 45	8	1413-433
257	Plug 1/4"	1	1343-025
258	Gasket ring dia. 21/14 x 2,0	1	1331-428
259	O-ring dia. 20,22 x 3,53	1	1331-019
	Non-return (check) valve
260	Valve cone	1	3042-107
261	Spring	1	1523-033
262	Cylinder screw M10 x 25	1	1413-371
263	Adaptor	1	3042-079
264	Tape bearing dim 10x1 x 136	2	2132-099
265	Locking device for non-retun valve	1	3042-108
266	Pointed screw M6 x 6	1	1413-229
	Suction side connection
279	Flange	1	3013-130
280	Cylinder screw M16 x 45	8	1413-433
281	O-ring dia 190.09 x 3.53	1	1331-105
	Economizer inlet
290	Flange with plug	1	3013-135
291	Cylinder screw M10 x 30	2	1413-372
292	O-ring dia 29.74 x 3.53	1	1331-025
	HLI Inlet
300	Flange with plug	2	3013-136
301	Cylinder screw M10 x 30	4	1413-372
302	O-ring dia 20.22 x 3.53	2	1331-019
	Connecting parts for slide rod
310	Washer for slide rod	1	3043-108
311	Cylinder screw M10 x 55	1	1413-377
	External oil piping
320-1	Pipe set complete, female drive	1	3049-021
320-2	Pipe set complete, male drive	1	3049-031
325-1	Orifice dia. 5,0 for oil injection pipe - R717	1	3142-052
325-2	Orifice dia. 3,2 for oil injection pipe - R22 and HFC's	1	3142-054
331	Plug 1/2"	1	1343-027
332	Gasket ring dia. 28,5/21.6 x 2,3	1	1331-430
333	Plug 1/4"	1	1343-025
334	Gasket ring dia. 24/14 x 2,0	1	1331-428
335	Plug 1/4"	1	1343-025
336	Gasket ring dia. 21/14x2,0	1	1331-428
337	Plug 3/4"	1	1343-028
338	Gasket dia. 34,93/27.13 x 2,34	1	1331-433
	Electrical signal transmitter for
	capacity slide position (optional)
350	Turning transmitter	1	3448-004
351.1	Sight-glass for transmitter	1	3045-007
352	Screw for transmitter	4	1412-012
	M3 x 8(included in pos. 350)
	Limitation of minimum capacity (optional)
228	Spacer ring for SAB 128H	1	3045-028
229	O-ring dia. 82.14x3.53	1	1331-077
210.2	Spindle
	replaces pos. 210.1	1	3045-063
	Limitation of minimum capacity (optional)
75.2	Glass for indicator, SAB 128/163
	replaces pos. 75.1	1	3045-036
351.2	Glass for indicator for turning transmitter, SAB 128/163 replaces pos. 351.1	1	3045-037
	Oil filter parts
450	Cover	1	3041-008
452	O-ring dia 132,94 x 3,53	1	1331-093
453	O-ring dia 101,19 x 3.53	1	1331-083
455	Locking nut M10	1	1433-080
456	Cylinder screw	4	1413-387
458	Stay bolt	1	2111-129
459	Magnet	4	1517-022
460	Intermediate ring	4	3424-039
461	Elastomer ring	2	1334-012
470	Filter element	1	1517-121
471	Plug 1/4"	1	1343-025
472	Gasket ring dia. 21/14 x 2,0	1	1331-428
473	O-ring dia. 20,22 x 3,53	1	1331-019
480	Filter housing	1	3042-084
481	O-ring dia 183,74 x 3,53	1	1331-104
482	Cylinder screw M8 x 25	4	1413-357
483	Pointed screw M6 x 8	3	1413-230
	Flow switch arrangement
500	Terminal box	1	1554.001
505	Nippel	1	2314-106
506	Dowty ring 34,9/27,1 x 2,3	1	1331-433
507	Flow switch with ball	1	1553-024
508	Washer	1	2114-046
509	Gasket ring 19/14 x 1,5	1	2356-124
510	Spring	1	2144-041
511	Circlip (part of pos. 507)	1
	Compressor relief valve system
700-1	Back pressure independent safety valve,	1	2416-202
	BSV8, 18 bar
700-2	Back pressure independent safety valve,	1	2416-203
	BSV8, 20 bar
700-3	Back pressure independent safety valve,	1	2416-204
	BSV8. 21 bar
700-4	Back pressure independent safety valve,	1	2416-224
	BSV8, 22 bar
700-5	Back pressure independent safety valve,	1	2416-205
	BSV8, 25 bar
701	Connection line, POV 40, dia. 12	1	3014-013
702	Cylinder screw M12 x 35	4	1413-387
703	O-ring dia. 82,14x3,53	1	1331-077
704	Main valve POV 40 including connection pipe	1	3014-011
715	Cover	1	3013-180
716	Cylinder screw M14 x 90	4	1413-417
717	O-ring dia. 69,44 x 3,53	1	1331-073
721	Cylinder screw M12 x 30	4	1413-386
722	O-ring dia. 63,09 x 3.53	1	1331-071
725	Banjo coupling	1	1349-091
726	Al gasket, dia, 24/13 x 1,5	1	2356-127
727	Reducer G 3/4-G 3/8"	1	2312-038
730	Union nut G 1"-3/8"	1	2469-070
732	Al gasket, dia- 30/16 x 1,5	1	2356-137
	Temperature/pressure transducers
751	Pressure transducer, suction gas (PT1)	1	1373-249
752	Pressure transducer, oil after filter (PT3)	1	1373-271
753	Pressure transducer, oil before filter (PT4)	1	1373-271
755	Coupfing 10-RL	2	1349-137
756	Elbow coupling 10-RL	1	1349-154
761	Temperature transmitter, compressor oil (TT6)	1	1373-281
762	Temperature transmitter, suction gas (TT7)	1	1373-282
765	Gasket ring - DKA R 1/4	2	1349-135

Spare parts survey for SAB 128 Mk3 unit

Regulating & Control delice	Pos.	Designation	Part no.
		UNISAB II
	PT1	Pressure transducer -1-9 bar	1373-249
	PT2	Pressure transducer -1 - 25 bar	1373-250
	PT3	See PT2
	PT4	See PT2
	TT5/6/7	Temperature transducer PT100	1373-264
	GT8	Position transmitter (capacity)	3448-004
	GT9	See GT8
		UNISAB II Frontpanel	1573-007
		1 CPU-module	1572-017
		1 Relay print	1574-014
		1 EPROM extractor	1613-002
		1 EEPROM extractor	1613-003
		1 EEPROM	1571-015

		3 Jumpers
		2 Fuses	1572-018
		1 Screw driver
Refrigerant system		Suction:
	20	O-ring dia 132,94 x 3,53	1331-093
		Set of gaskets for SCV80 (R717)	3184-078
		Set of gaskets for SCV100 (R22)	3184-079
	24
	34-35	Set of gaskets for SNV 8	2453-053
	47-48
		Oil separator, general:
	30	Sealing ring dia. 42/49 x 6,5	1349-213
	30	Heating rod, 250 V	3181-038
		Heating rod. 115V	3181-039
		Heating rod, 230	3181-040

	31	O-ring dia 52.07 x 2.62 (sight glass)	1331-140
		Sight glass	1226-017

	55	O-ring dia 329,57 x 5,33 (for cover)	1331-184
		Oil seperating element	1517-062

		Oil return:
	52	Nozzle valve	1364-151
	53	Sight glass	1226-014
	53	Gasket dia. 40.5/33 x 1.5	2356-144

		Discharge:
	204	Set of gaskets for SCV65	3184-078
		O-ring dia 78,97 x 3,53	1331-076

	22	Safety valves:
	28	DN 25/40
		Gasket, dia. 57/43 x 2	2356-260
		Gasket, dia. 75/61 x 2	2356-220
		O-ring dia. 61,60 x 2,62 (house)	1331-143
		Conical seal for DN 25/40	1365-077
		Spring (for 25 Bar opening pressure)	1365-046

	28	DN 40/65
		Gasket, dia. 75/61 x 2	2356-220
		Gasket, dia. 109/95 x 2	2356-222
		O-ring dia. 91,94 x 3,53	1331-080
		Conical seal for DN 43,65	1365-079
		Spring (for 25 Bar opening pressure)	1523-027

Oil system		Flange connection, oil tube
		Gasket, dia 57/43 x 2	2356-260
		O-ring dia 59,92 x 3,53 (compr.)	1331-071

		Oil by-pass (at pump)
	210	Gasket, dia 102/55 x 1,5 (non-return valve)	2356-092
		O-ring dia 26.57 x 3,53 (non-return valve)	1331-023

	69	Pressure build up for capacity reg.
		Non-return valve 18, 1 bar	1364-004
		Non-return valve 10, 02 bar	1364-008

		Oil pump
	63	Shaft seal complete	1332-192
	63	O-ring dia 44,12 x 2,62 (cover for pump)	1331-146
	64-65	Set of gaskets for SVA 15	2453-022
	60-62	Set of gaskets for SVA 32
	61	Filter element 150	2464-233
	61	O-ring dia 44,04 x 3,53	1331-022
	61	O-ring dia 36,09 x 3,53	1331-018
	61	O-ring dia 13.94 x 2,62	1331-014

Capacity regulation	46	Thermostatic three-way valve, type RT3
		O-ring, Neoprene	1331-383
		Thermo element, 48°C	1365-005

	70	Solenoid valve block
		Valve housing EVM (NC)	1372-335
		Gasket set for EVM (NC/NO)	1336-024
		Coil 10W 220V 50/60 Hz	1372-330
		110V 50/60 Hz	1372-331
		250V 50/60 Hz	1372-334

	71	Solenoid valve:
		Valve housing EVM (NO)	1372-425
		Gasket set for EVM	1336-024
		Throttle valve
	72	Gasket set 6F	1377-210
	73	Solenoid valve:
		See pos. 70
	74	Solenoid valve:

BLI Oil cooling	80-84	Gasket set for SVA 15-20	2453-022

	81	Filter FA15:
		(When TEAT 20 is selected)
		Gasket set for FA15	1377-078
		Repair kit for FA15	1377-250

	81	Filter FA20:
		(When TEAT 85 is selected)

		Gasket set for FA20	1377-079
		Repair kit for FA20	1377-251

	82	Solenoid valve EVRA15
		(when TEAT 20 is selected)

		Gasket set (for EVRA15)	1377-093
		Repair kit (for EVRA15)	1377-099
		Coil 10W 220V 50/60 Hz
		110V 50/60 Hz See pos 70
		250 V 50/60 Hz
	82	Solenoid valve EVRA20
		(when TEAT 85 is selected)

		Gasket set (for EVRA 20)	1377-094
		Repair kit (for EVRA20)	1377-069
		Coil 10W 220V 50/60 Hz
		110V 50/60 Hz See pos 70
		250 V 50/60 Hz

	83	Injection valve TEAT 82
		Nozzle insert 20-5	1371-202
		Nozzle insert 20-8	1371-203
		Nozzle insert 20-12	1371-204
		Nozzle insert 21-20	1371-206
		Thermal part 351B5 deg.C	1371-255
		Thermal part 55-95 deg.C	1371-253

	83	Injection valve TEAT 85
		Nozzle insert 85-33	1371-207
		Nozzle insert 85-55	1371-208
		Nozzle insert 85-85	1371-209
		Thermal part 35-65 deg. C	1371-257
		Thermal part 55-95 deg.C	1371-250

Compr.con- nections		Spare parts set for coupling S952 size 225
		Sheets, bolts, nuts & slices	1524-124
		Spacer bushing	1526-002
		Stop screw M10 x 10	1413-250
		Combination wrench 1/2"	Compr.
		Box wrench 1/2"	Tools

		Alignment motor - compressor
		Discs (motor up to IEC 280)	2221-067
		Discs (motor from IEC 315)	2221-076
		Tools	3183-104

Line no A401 = Normal set (part no. 3083-044)
Line no. A402 = Extended set (part no. 3083-046)
Line no. B401 = Tools for coupling alignment (part no 3183-104)
Line no. B40 = Tools for shaft seal removal, oil pump (part no 3083-160)

Tool no.	Designation	Part no.	A401	A402	B401	B402
1	Puller for bearings	3083-060	1	1
2	Thrust ring for the puller, female	3083-043	1	1
3	Thrust ring for the puller, male	3083-127	1	1
4	Tool for fitting the bearings	3083-062	1	1
5	Ring for the puller	3083-042	1	1
6	Tool for pressing out the rotors	3083-063	1	1
7	Tool for fitting the bearings	3083-061	1	1
8.1	Retaining cup for male rotor	3083-097	1	1
8.2	Retaining cup for female rotor	3083-098	1	1
9	Tool for dismounting the bearings	3083-041	2	2
10	Thrust washer	3083-002	1	1
11	Locking tool for rotor	3083-126	1	1
20.1	Threaded pin M10 x 160	2112-129	4	4
20.2	Threaded pin M12 x 275	2112-148	1	1
21.1	Hexagon head screw M16 x 130	1424-271	1	1
21.2	Hexagon head screw M10 x 130	1424-203	4	4
22.2	Socket cap screw M8 x 35	1413-359	1	1
22.3	Socket cap screw M8 x 120	1413-314	2	2
22.4	Socket cap screw M10 x 25	1413-371	4	4
22.6	Socket cap screw M12 x 35	1413-387	1	1
22.7	Socket cap screw M12 x 90	1413-400	1	1
23.1	Nuts M8 Nuts M12	1432-063	2	2
23.2	Nuts M10	1432-064	4	4
23.3	Nuts M12	1432-065	1	1
24.1	Washer dia. 24/13 x 2.5	1436-036	1	1
24.2	Washer dia. 35/13 x 5	1436-140	3	3
25	Guide pin M16 x 300	2112-147	2	2
30	Tool for adjusting the bearings	3083-096	1	1
31	Special screw for adjusting the bearings	3083-095	1	1
32.1	Eye bolt M12	1427-150	1	1
32.2	Eye bolt M16	1427-156	1	1
33	Alignment device for coupling	3183-104			1
34	Feeler gauge	1622-050			1
36	Tools for shaft seal removal, oil pump Consist of:
36.1	Pullef for shaft seal, oil pump	3083-157				1
36.2	Cap screw M10 x 75	1424-201				1
36.3	Threaded pin M8 x 150	3083-156				3
36.4	Nut M8	1432-063				3
36.5	Punch dia. 18 x 60	3063-158				1
36.6	Punch dia. 22/16,5 x 100	3083-159				1
40.1	Torque wrench(Ratchet) 5 - 50 Nm 1/2"			1
40.2	Torque wrench 40-200 Nm (14 x 18)			1
42	Extension 1/2"			1
43	Converter for torque wench(14x18) - 1/2"			1
44.1	Hexagon bit adapter 1/2" - 4mm			1
44.2	Hexagon bil adapter 1/2" - 5mm			1
44.3	Hexagon bit adapter 1/2"- 6mm			1
44.4	Hexagon bit adapter 1/2" - 8mm			1
44,5	Hexagon bit adapter 1/2" - 10mm			1
44.6	Hexagon bit adapter 1/2" - 14mm			1
45	Box spanner insert 1/2" - 19mm			1
45.1	Box spanner insert 1/2" - 24mm			1
45.2	Box spanner insert 1/2" - 27mm			1
45.3	Box spanner insert 1/2" -36mm			1
45.4	Box spanner insert 1/2" -1/2"			1
46	Open end spanner (14x18) - 19mm			1
50.1	Combination spanner 17mm	1613-276		1
50.2	Combination spanrer 19mm	1612-277		1
50.3	Conbination spanner 1/2"
51.1	Allen key for socket cap screw 3mm	1512-395		1
51.2	Allen key for socket cap screw 5mm	1612-397		1
51.3	Allen key for socket cap screw 6mm	1612-398		1
51.4	Allen key for socket cap screw 8mm	1612-399		1
51.5	Allen key for socket cap screw 10mm	1612-401		1
51.6	Allen key for socket cap screw 14mm	1612-400		1
52	Magnetic Fixture for dial indicator			1
53	Dial indicator			1
54.1	Retaining ring pliers			1
54,2	Retaining ring pliers			1
55.1	Hammer	1612-012		1
55.2	Plastic hammer	1612-042		.1
56	Steel punch 8 mm			1
57	Pliers for driving pin	1612-190		1

По вопросам возможности поставки или наличия запчастей, специальных инструментов, возможности сервисного обслуживания или ремонта компрессора Sabroe обращайтесь по телефону в Санкт-Петербурге +7(904)609-54-05 или по электронной почте info@torosspb.ru, storopov86@gmail.com