Запасные части к компрессорам Sabroe SAB163

Pos.	Designation	Quantity		Part no.
		Aut.Vi	Man.Vi
	Complete compressor, female drive, Man.Vi		1(F)	4161-069
	Complete compressor, female drive, Aut. V,	1(F)		4161-070
	Complete compressor, male driva, Man. Vi		1(M)	4161-071
	Complete compressor, male driva, Aut.Vi	1(M)		4161-073
	Compressor housing
10	Rotor housing, SAB -163H	1	1	3011-020
	Bearmg cover at suction end
20	Suction cover for SAB 163 M	1	1	3013-141
21	O-ring 380.37 x 5.33	1	1	1331-187
22	Cylindrical pin dia. 16 x 50	2	2	1445-091
23	Cylinder screw M16 x 45	16	16	1413-433
24	Plug with collar 1/2"	1	1	1343-027
25	Aluminium gasket dia. 27/21 x 1,5	1	1	2356-133
	Bearing cover at discharge end
40	Cover for bearings	1	1	3013-017
43	Cylinder screw M10 x 35	6	6	1413-373
44	Adjusting screw M20	2	2	2111-122
45	Locking screw M6 x 10	4	4	1413-231
	Capacity regulating cylinder
50	Capacity cylinder	1	1	3043-009
51	O-rlng 107.54 x 3.53	1	1	1331-085
52	Cylinder screw M12 x 40	3	3	1413-358
	Cover for capacity regulating cylinder
60	Cover for capacity cylinder	1	1	3013-194
61	O-ring 120.24 x 3.53	1	1	1331-089
62	Cylinder screw M12 x 30	4	4	1413-386
	Housing for capacity indicator
70	Capacity indicator housing	1	1	3045-002
71	Cylinder screw M6 x 30	4	4	1413-343
72	Capacity indicator cover	1	1	3045-003
73	Cylinder screw M6 x 50	4	4	1413-347
74	O-ring 98.02 x 3.53	1	1	1331-081
75.1	Sight glass for capacity indicator	1	1	3045-006
	Shaft seal cover
80-1	Shaft seal cover, before jure 1998	1	1	3013-142
80-2	Shaft seal cover, before jure 1998	1	1	3013-209
81	O-ring 113.89 x 3,53	1	1	1331-087
82-1	Cylinder screw M12 x 50, before june 1998	1	1	1413-390
82-2	Cylinder screw M12 x 35, before june 1999	2	2	1413-367
82-3	Cylrnder screw M12 x 35, after june 1998	4	4	1413-387
83	Driving pin dia. 4 x 6	1	1	1446-011
84	Plug with rim 1/4"	1	1	1343-025
85	Gasket dia. 19/14 x 1,5	1	1	2356-124
86	Hose connecting branch '1/4"	1	1	1345-143
87	Clear plastic hose 3/16" x 300 mm	1	1	1241-190
88	Plug with rim 3/8", before june 1998	1	1	1343-026
89	Dowty ring dia 23,8/17,35 x 2, before june 1998	1	1	1331-427
	Cap cover
90	Cap cover	1	1	3013-036
91	O-ring 113.89 x 3.53	1	1	1331-087
92	Cylinder screw M12 x 35	3	3	1413-387
	Cover for slide stop
100	Slide stop cover		1	3013-068
101	O-ring 78,97 x 3.53		1	1331-076
102	Cylinder screw M12 x 35		4	1413-387
103	Bearing retainer		1	3021-018
104	Cylinder screw M6 x 20		4	1413-341
105	Locking plate		1	2114-043
	Rotors and suction end bearings
110	Rotor set for SAB 163 H, female drive	1(F)	1(F)	3024-006
110	Rotor set for SAB 1631H, male drive	1(M)	1(M)	3024-106
111	Radial roller bearing	2	2	1513-017
113	Oil splash ring external dia. 46	1	1	1437-287
114	Washer for bearing	2	2	3021-007
115	Cylinder screw M16 x 45	2	2	1413-433
118	Driving pin dia. 4.0 x 10	1	1	1446-012
119	Retainer pin	2	2	3021-009
120	Balance piston, suction end	1	1	3025-008
	Discharge end bearings, female rotor
130	Balance piston dia. 86	1	1	3025-037
131	Radial roller bearing dia. 55/120 x 43	1	1	1513-017
132	Four point bearing dia 55/120 x 29	1	1	1513-029
133	Set of shims dia. 100/120, for adjusting the
	clearance between the rotors and outlet ports,	1	1	2124-082
	Comprising; 1 off thickness 0.49 mm
	1 off - 0.52 mm
	1 off - 0.55 mm
	1 off - 0.56 mm
	1 off - 0.61 mm
	1 off - 0.64 mm
	1 off - 0.67 mm
	Discharge end bearings, mate rotor
135	Balance piston dia. 86	1	1	3025-037
136	Radial roller bearing dia.60/130 x 46	1	1	1513-013
137	Four point bearing dia.60/130 x 31	1	1	1513-030
138	Set of shims dia. 105/130 for adjustnig the.
	clearance between, the rotors and outlet ports,	1	1	2124-083
	Comprising 1off thickness 0.49 mm
	1 off - 0.52 mm
	1 off - 0.55 mm
	1 off - 0.58mm
	1 off - 0.61 mm
	1 off - 0.64 mm
	1off - 0.67 mm
	Discharge end ports
140	Outlet port (male rotor)	1	1	3031-035
141	Outlet port (femle rotor)	1	1	3031-036
142	Cylinder screw M10 x 150	6	6	1413-376
143	Steel gasket dia. 16/10 x 2	6	6	2351-030
144	Set screw M10 x 20 (first production series)	2	2	1413-252
145	Set screw M10 x 10 (first production series)	2	2	1413-250
146	Blank-off screw	2	2	1343-026
147	Locking screw M 10 x 10 (new productian series)	2	2	1413-253
148	Adjusting screw M10 x 20 (new productian series)	2	2	1413-032
149	Gasket	2	2	1331-427
	Parts for adjusting rotors
151	Inner cover (male rotor)	1	1	3013-019
152	O-ring 123.42 x 3.53	1	1	1331-090
153	Inner cover (female rotor)	1	1	3013-045
154	O-ring 113.89 x 3.53	1	1	1331-087
	Shaft seal
160	Shaft seal type 680	1	1	3084-529
	Suction filter
170	Suction filter	1	1	3042-081
171	Set screw M6x 10	3	3	1413-231
	Adjusting system for V_i-slide
180	Spindle for slide stop		1	3044-012
182	Sealing washer for slide stop		1	3044-014
183	Sealing ring dia 28/22		1	1331-503
184	O-ring 44.04 x 3.53		1	1331-065
186	Axial ball bearing dia. 42/25 x 11		2	1512-015
	Slide stop
190	Slide stop (included in pos.192 and pos. 370)
	Man. V_i- slide
191	Spring	1	1	1523-162
192	Slide control (including slide stop, pos. 190)		1	3044-066
193	Cylinder screw M10 x 12	1	1	1413-408
	Capacity regulating slide
200	Capacity slide	1	1	3043-174
201	Inner piston slide	1	1	3043-092
202	Outer piston slide	1	1	3043-093
203	O-ring 53.57 x 3.53	1	1	1331-068
204	Gasket	1	1	1332-107
205	Cylindrical pin dia. 6 x 12 (included in pos no 207)	(1)	(1)	1445-075
206	Cylinder screw M6 x 25	4	4	1413-342
207	Slide rod	1	1	3043-111
208	Tape bearing	2	2	2132-104
209	O-ring 21.62 x 3.53	1	1	1331-020
	Spindle for capacity regulation
210.1	Spindle for capacity indicator	1	1	3045-058
216	Magnetic coupling	1	1	3045-061
217	O-ring dia 44,12 x 2,62 (incl.in pos.216)	(1)	(1)	1331-146
218	Hexagon head screw M4 x 16 (inci. in pos. 216)	(1)	(1)	1413-320
219	Hexagon head screw M4 x 20 (incl. in pos. 216)	(2)	(2)	1413-322
	Capacity indication
221	Indicator dial	1	1	3045-001
233	Cylinder screw M4 x 10	1	1	1413-319
224	Supporting ring	1	1	2356-155
226	Locking washer DC 15/8,4	1	1	1437-054
227	Locking washer DC 8/4,3	1	1	1437-060
	Suction gas inlet
252	O-ring dia.190.09 x 3.53	1	1	1331-105
253	Inlet flange	1	1	3013-130
254	Cylinder screw M 16 x 45	8	8	1413-433
257	Plug 1/4"	1	1	1343-025
258	Gaskel ring dia. 21/14 x 2,0	1	1	1331-428
259	O-ring dia. 20,22 x 3,53	1	1	1331-019
	Non-return valve
260	Valve cone	1	1	3042-107
261	Spring	1	1	1523-033
262	Cylinder screw M10 x 25	1	1	1413-371
263	Adaptor	1	1	3042-079
264	Tape bearing dim 10 x 1 x 136	2	2	2132-125
265	Locking device	1	1	3042-108
266	Pointed screw M6 x 6	1	1	1413-229
	Suction side connection
279	Flange	1	1	3013-130
280	Cylinder screw M 16 x 45	8	8	1413-433
281	O-ring 190.09 x 3.53	1	1	1331-105
	Economizer inlet
290	ECO plug	1	1	3013-128
291	Cylinder screw M10 x 30	1	1	1413-372
292	O-ring 37.69 x 3.53	1	1	1331-030
293	Cylinder screw M8 x 25	1	1	1413-357
	HLI inlet
300	HLI plug	2	2	3013-127
301	Cylinder screw M10 x 30	4	4	1413-372
302	O-ring 23.39 x 3,53	2	2	1331-022
	Connecting parts for slide rod
310	Washer for slide rod	1	1	3043-109
310	Cylinder screw M10 x 65	1	1	1413-383
	Internal oil piping
320-1	Pipe set complete, female drive, before june 1998	1	1	3049-045
320-2	Pipe set complete, male drive, before june 1998	1	1	3049-030
320-3	Pipe set complete, female drive, after june 1998	1	1	3049-045
320-4	Pips set complete, male drive, after june 1998	1	1	3049-046
325.1	Orifice dia. 7 for oil injection pipe - R717	1	1	3142-062
325.2	Orifice dia. 5 for oil injection pipe - R22 and HFC's	1	1	3142-052
331	Plug 1/3"	1	1	1343-027
332	Gasket ring dia. 28,5/21,6 x 2,3	1	1	1331-430
333	Plug 1/4"	1	1	1343-025
334	Gasket ring dia. 21/14 x 2,0	1	1	1331-428
335	Plug 1/4"	1	1	1343-025
336	Gasket ring dia. 21/14 x 2,0	1	1	1331-428
337	Plug 3/4"	1	1	1343-028
338	Gasket ring dia 34,93/27,13 x 2,34	1	1	1331-433
	Electrical signal transmitter for
	capacity slide positon (optional)
350	Turning transmitter	1	1	3448-004
351.1	Sight glass for transmitter	1	1	3045-007
352	Screw for transmitter M3 x 8 (inducted in pos. 350)	4	4	1412-012
	Limitation of minimum capacity (optional)
228	Spacer ring for SAB 163H	1	1	3045-029
229	O-ring dia. 113.89 x 3.53	1	1	1331-087
210.2	Spindle
	(replaces pos. 210.1)	1	1	3045-064
75.2	Glass for indicator, SAB 128/163
	(replaces pos. 75.1)	1	1	3045-036
351.2	Giass for indicator, SAB 128/163 for turning transmitter
	(replaces pos. 351.1)	1	1	3045-037
	Aut. V_i slide
370	Slide control for auto. V_i
	(including slide stop pos.190)	1		3044-065
371	Gasket dia. 72	1		1333-119
372	Piston for Auto. V_i	1		3044-042
373	Cylindrical pin dia. 6 x 12
	(included in pos. 372)			1445-075
374	Cylinder screw M6 x 12	4		1413-339
	Cover for slide stop
380	Slide stop cover for auto. V_i	1		3013-195
381	O-ring 78.97 x 3.53	1		1331-076
382	Cylinder screw M12 x 30	4		1413-386
383	Cylindrical pin dia 8 x 24	1		1445-077
	Spindle for V\| indication
390	Spindle for auto. V_i	1		3044-062
395	Driving disc	1		3044-021
396	Cylinder screw M 4x 12	1		1413-318
	Bearing retainer Tor Aut. V_i
400	Bearing retainer tor aut. V_i	1		3044-064
401	Cylinder screw M6 x 45	4		1413-307
402	Cover for the transmitter	1		3045-009
403	Cylinder screw M4 x 10	4		1413-319
405	Magnetic coupling	1		3045-062
406	O-ring dia. 32,09 x 2,62 (incl. in pos. 405)	(1)		1331-133
407	Hexagon head screw M4 x 16 (incl. in pos. 405)	(1)		1413-320
	Electrical signal transmitter for
	V_i-slide position (optional)
410	Turning transmitter	1		3448-004
411	Driving lug	1		3044-020
413	Pointed screw M4 x 5	1		1413-211
413	Clamping pin dia. 1,5 x 12	1		1446-010
415	Screw for transmitter M3 x 8 (included in pos. 410)	4		1412-012
	Oil filter parts
450	Cover	1	1	3041-008
452	O-rmg dia 132,94 x 3,53	1	1	1331-093
453	O-ring dia 101,19 x 3,53	1	1	1331-083
455	Locking nut M10	1	1	1433-080
456	Cylinder screw Ml12 x 30	4	4	1413-386
458	Slay bolt	1	1	2111-129
459	Magnet	4	4	1517-022
460	Intermediate ring	4	4	3424-039
461	Elastomer ring	2	2	1334-012
470	Filter element	1	1	1517-121
471	Piug 1/4"	1	1	1343-025
472	Gasket ring dia. 21/14 x 2,0	1	1	1331-428
473	O-ring dia. 20,22 x 3,53	1	1	1331-019
480	Filter housing	1	1	3042-084
481	O-ring dia 183.74 x 3.53 (new production series)	1	1	1331-104
432	Cylinder screw M8 x 25	4	4	1413-357
483	Pointed screw M6 x 8	3	3	1413-230
	Ftow switch arrarngement
500	Terminal box	1	1	1554-001
505	Nippel	1	1	2314-106
506	Dowty ring 34,9/27,1 x 2.3	1	1	1331-433
507	Flow switch with ball	1	1	1553-024
508	Washer	1	1	2114-046
509	Gasket ring 19/14 x 1,5	1	1	2356-124
510	Spring	1	1	2144-041
511	Circlip (part of pos. 507)	1	1
	Compressor relief valve system
700-1	Back pressure independent safety valve BSV8, 18 bar	1	1	2416-202
700-2	Back pressure independent safety valve BSV8, 20 bar	1	1	2416-203
700-3	Back pressure independent safety valve BSV8, 21bar	1		2416-204
700-4	Back pressure independent safety valve BSV8, 22 bar	1		2416-224
700-5	Back pressure independent safety valve BSV8, 25 bar	1		2416-205
701-1	Connection line, POV 40, dia. 12	1		3014-014
701-2	Connection line, POV 50. dia. 12	1		3014-015
702	Cylinder screw M12 x 35	4	4	1413-387
703	O-ring dia. 82,14 x 3,53	1	1	1331-077
704-1	Main valve POV 40 including conneection pipe	1	1	3014-005
704-2	Main valve POV 50 including conneection pipe	1	1	3014-008
715	Cover	1	1	3013-177
716	Cylinder screw M16 x 40	4	4	1413-432
717	O-ring dia, 132,94 x 3,53	1	1	1331-093
721	Cylinder screw M12 x 30	4	4	1413-386
722	O-ring dia. 63,09 x 3,53	1	1	1331-071
725	Banjo coupling	1	1	1349-091
726	Al gasket, dia 24/13 x 1,5	1	1	2356-127
727	Reduced G 3/4" -G3/8" .	1	1	2312-038
730	Union nut G 1" - G 3/8".	1	1	2469-070
732	Al gasket, dia. 30/16 x 1,5	1	1	2356-137
	Temperature/pressure transducers
751	Pressure transducer, suction gas (PT1)	1	1	1373-249
752	Pressure transducer, oil after filter (PT3)	1	1	1373-271
753	Pressure transducer, oil before filter (PT4)	1	1	1373-271
755	Coupling 10-RL	2	2	1349-137
755	Elbow coupling 10-RL	1	1	1349-233
761	Temperature transmitter, compressor oil (TT6)	1	1	1373-281
752	Temperature transmitter,suction gas (TT7)	1	1	1373-282
765	Gasket ring DKA R 1/4	2	2	1349-135

Spare parts survey for SAB 163 Mk3 unit

The following list comprises all components that can be fitted on a compressor unit.

From this list we have selected the components that are used on a particular unit and which are indicated on the piping diagram of this instruction manual.

The position numbers on the piping diagram are a reference to the ”Pos.” columns of this list. The piping diagram is dedicated to the compressor number stated on page 1 of this instruction manual.

The components in the shaded areas are variable. This may be due to voltage, refrigerant, approved pressure etc.

On ordering spare parts it may be an advantage to receive them in sets selected for your specific compressor unit.

A list of sets can had on request from SABROE’s local representative.

Pos.	Designation	Part no.
Regulating & Control device		UNISAB II
	PT1	Pressure transducer -1 - 9 bar	1373-249
	PT2	Pressure transducer -1 -25 bar	1373-271
	PT3	See PT2
	PT4	See PT2
	TT5/6/7	Temperature transducer PT100	1373-264
	GT8	Position transmitter (capacity)	3448-004
	GT9	See GT8
		UNIBAB II Frontpanel	1573-007
		1 CPU-module	1572-026
		1 Ralay print	1574-016
		1 EPROM extractor	1613-002
		1 EEPROM exctractor	1613-003
		1 EEPROM	1571-015.1
		3 Jumpers
		2 Fuses	1572-018
		1 Screw driver
Refrigerant system		Suction:
	20	O-ring dia 132,94 x 3,53	1331-093
		Set of gaskets for SCV100 (R717)	3184-079
		Set of gaskets for SCV150 (R22)	3184-081
	24
	34-35	Set of gaskets for SNV 8	2453-053
	47-48
		Oil separator, general:
	30	Sealing ring dia. 42/49 x 6,5	1349-213
	30	Heating rod, 250 V	3181-038
		Heating rod, 115V	3181-039
		Heating rod, 230	3181-040

	31	O-ring dia 52,07 x 2,62 (sight glass)	1331-140
		Sight glass	1226-017

	55	O-ring dia 329,57 x 5,33 (tor cover)	1331-184
	55	Oil separating element	1517-061

		Oil return:
	52	Nozzle valve	1364-151
	53	Sight glass	1226-014
	53	Gasket dia. 40.5/33 x 1.5	2356-144

		Discharge:
	204	Set of gaskets for SCV100	3184-079
		O-ring dia 120,4 x 3,53	1331-089

	22	Safety valves:
	28	DM 32/50
		Gasket, dia. 75/61 x 2.0	2356-220
		Gasket, dia. 109/95 x 2.0	2356-222
		O-rirg dia. 91.67 x 3.53 (house)	1331-060
		Conical seat for DN 32/50	1365-079
		Spring (for 25 Bar opening pressure)	1365-048
		DN 50/80
		Gasket, dia, 87/73 x 2.0	2356-221
		Gasket, dia, 120/106 x 2.0	2356-223
		O-ring dia. 117.07 x 3.53 (house)	1331-088
		Conical seal for DN 50/8O	1365-080
		Spring (for 25 Bar opening pressure)	1365-050
Oil system		Flange connection, oil tube
		Gasket, dia 75/61 x 2,0	2356-220
		O-ring dia 59.92 x 3.53 (compr.)	1331-071
		Oil by-pass (at pump)
		Gasket, dia 131/95 x 1,5 (non-return valve)	2356-104
		O-ring dia 40,94 x 2,62 (non-return valve)	1331-298
		Pressure build up for capacity reg.
		Non-return valve 18,1 bar	1364-009
		Non-return valve 10,02 bar	1364-008
		Oil pump
	63	Shaft seal complete	1332-192
	63	O-ring dia 44,12 x 2,62 (cover for pump)	1331-146
	64-65	Set of gaskets for SVA 15	2453-022
	60-62	Set of gaskets for SVA 32
	61	Fitler element 150	2464-233
	61	O-ring dia 44.04 x 3,53	1331-022
	61	O-ring dia 36,09 x 3,53	1331-029
	61	O-ring dia 13,94 x 2,62	1331-014
Capacity regulation	46	Thermostatic three-way valve, type RT5
		O-ring, Neoprene	1331-383
		Thermo element, 48'C	1365-005
	70	Solenoid valve block
		Valve housing EVM (NC)	1372-335
		Gasket set for EVM (NC/NO)	1336-024
		Coil 10 W 220 V 50/60Hz	1372-537
		110 V 50/60Hz	1372-538
		240 V 50Hz	1372-539
	71	Solenoid valve
		Valve housing EVM (NO)	1372-425
		Gasket set for EVM	1336-024
		Throttle valve
	72	Gasket set 6F	1377-210
	73	Solenoid valve:
		See pos.70
	74	Solenoid valve
BLI Oil cooling	80-84	Gatket set for SVA 15-20	2453-022
	81	Filter FA15:
		(When TEAT 28 is selected)
		Gasket set for FA15	1377-078
		Repair kit for FA15	1377-250

		Filter FA20:
	81	(When TEAT 85 is setected)
		Gasket set for FA20	1377-079
		Repair kit for FA20	1377-251

	82	Solenoid valve EVRA15
		(whenTEAT 20 is selected)
		Gasket set (for EVRA15)	1377-093
		Repair kit (for EVRA 15)	1377-099
		Coil 10W 220 V 50/60 Hz
		110 V 50/60 Hz See pes 70
		240 V 50 Hz
	82	Solenoid valve EVRA20
		(when TEAT 85 is selected)
		Gasket set (for EVRA 20)	1377-094
		Repair kit (for EVRA 20)	1377-069
		Coil 10W 220 V 50/60 Hz
		110 V 50/60 Hz See pes 70
		240 V 50 Hz
	83	Injection valve TEAT 20
		Nozzle insert 20-8	1371-203
		Nozzle inset 20-12	1371-204
		Nozzle insert 20-20	1371-206
		Thermal part 35-65 deg. C	1371-255
		Thermal part 55-95 deg. C	1371-253
	83	Injection valve TEAT 85
		Nozzle insert 85-33	1371-207
		Nozzle Insert 85-55	1371-208
		Nozzle insert 85-85	1371-209
		Thermal part 35-65 deg. C	1371-257
		Thermal part 55-95 deg. C	1371-250
	83	Injection valve PMFL 80
		Gasket set	1377-040
		Piston rod	1377-086
Compr. connections		Spare parts set for coupling S952 size 262
		Sheets, bolts, nuts & slices	1524-125
		Spacer bushing	1526-003
		Stop screw M 10 x 10	1413-250
		Combination wrench 9/16"	Compr.
		Box wrench 9/16"	Tools
		Alignment motor - compressor
		Discs (motor up to IEC 280)	2221-067
		Discs ( motor from IEC 315)	2221-076
		Tools	3183-104

Line no. A401 = Normal set (part no. 3083-047)

Line no. A402 = Extendet set (part no. 3083-049 incl. 3083-048)

Line no. B401 = Tools for alining the coupling (part no. 3183-104)

Line no. B402 = Tools for shaft seal removal, oil pump (part no 3083-160)

Tools no.	Designation	Part no.	A401	A402	B401	B402
1	Pullar for bearings	3083-131	1	1
2	Thrust ring for the puller, female :	3083-130	1	1
3	Thrust ring for the puller, male	3083-054	1	1
4	Tools for fitting the bearings	3083-058	1	1
5	Ring for the puller	3083-053	1	1
6	Tools for pressing out the rotors	3083-132	1	1
7	Tools for fitting the bearings	3083-133	1	1
8.1	Retaining cup formate rotor	3083-102	1	1
8.2	Retaining cup for female rotor.	3083-103	1	1
9	Tools for dismounting the bearings	3083-052	2	2
10	Thrust washer	3083-129	1	1
11	Locking tool for rotor	3083-128	1	1
12	Bearing dia 42/25 x 11	1512-015	1	1
20.1	Threaded pins M10 x 160	2112-129	4	4
20.2	Threaded pin M16 x 325	2112-151	1	1
21.1	Hexagon head screw M20 x 120	1424-298	1	1
21.2	Hexagon head screw M10 x 130	1424-203	4	4
22.2	Socket cap screw M8 x 35	1413-359	1	1
22.3	Socket cap screw M8 x 120	1413-314	1	1
22.4	Socket cap screw M10 x 25	1413-371	4	4
22.6	Socket cap screw M16 x 50	1413-434	1	1
22.7	Hexagon head screw M16 x 130	1424-113	1	1
23.1	Nuts M8	1432-063	2	2
23.2	Nuts M10	1432-064	4	4
23.3	Nuts M16	1432-067	1	1
24.2	Washer dia. 45/17 x 5	3083-114	4	4
25	Guide pin M16 x 300	2112-147	2	2
30	Tools for adjusting the bearings	3083-101	1	1
31	Special screw for adjusting the bearings	3083-100	1	1
32.2	Eye bolt M16	1427-156	1	1
33	Alignment device for coupling	3133-104			1
34	Feeler gauge	1622-050			1
36	Tools for shaft seal removal, oil pump Consists of:
33,1	Puller for shaft seal, oil pump	3083-157				1
36,2	Cap screw M10 x 75	1424-201				1
36,3	Threaded pin M8 x 150	3083-156				3
36,4	Nuts M8	1432-063				3
36,5	Punch dia. 18 x 80	3083-158				1
36,6	Punch dia. 22/16,5 x 100	3083-159				1
40.1	Torque wrench (Ratchet) 5 - 50 Nm 1/2"			1
40.2	Torque wrench 40-200 Nm (14 x 18)			1
42	Extention 1/2°			1
43	Converter for torque wench(14x18) - 1/2"			1
44.2	Hexagon bit adaptor 1/2" - 5mm			1
44.3	Hexagon bit adaptor 1/2" - 6mm			1
44.4	Hexagon bit adaptor 1/2" - 8mm			1
44.5	Hexagon bit adaptor 1/2" - 10mm			1
44.6	Hexagon bit adaptor 1/2" - 14mm			1
45	Box spanner insert 1/2" - 19mm			1
45.2	Box spanner insert 1/2" - 30mm			1
45,3	Box spanner insert 1/2" - 36mm			1
45.4	Box spanner insert 1/2"-9/16"			1
46	Open end spanner (14 x 18) - 24mm			1
50.1	Combination spanner 17mm	1612-276		1
50.2	Combination spanner 9/16"			1
51.1	Allen key for socket cap screw 3mm	1612-395		1
51.2	Allen key for socket cap screw 5mm	1612-397		1
51.3	Allen key for socket cap screw 6mm	1612-398		1
51.4	Allen key for socket cap screw 8mm	1612-399		1
51.5	Allen key for socket cap screw 10mm	1612-401		1
51.6	Allen key for socket cap screw 14mm	1612-400		1
52	Magnetic Fixture for dial indicator			1
53	Dial indicator			1
54.1	Retaining ring plier			1
54.2	Retaining ring plier			1
55.1	Hammer	1612-012		1
55.2	Plastics hammer	1612-042		1
56	Steel punch 10 mm			1
57	Plier for driving pin	1612-190		1

По вопросам возможности поставки или наличия запчастей, специальных инструментов, возможности сервисного обслуживания или ремонта компрессора Sabroe обращайтесь по телефону в Санкт-Петербурге +7(904)609-54-05 или по электронной почте info@torosspb.ru, storopov86@gmail.com